Lighter Replica Electronic Double Element

Reduce employment costs, reduce management expenses and industrial injury risks, and ensure the quality of products. There will be no material waste and too loose or too tight, which are adjusted accordingly.
What are the disadvantages of non-standard automation equipment in the application process? With the continuous improvement of scientific and technological level and production technology, more and more non-standard automation equipment are used. However, there are still some problems with non-standard automation equipment. These problems are mainly due to external reasons and the equipment itself.
From the perspective of the causes of defects, non-standard automation equipment can be divided into hard defects and soft defects, and the two defects can also exist together; Other disadvantages can also include static and dynamic disadvantages. Static disadvantages are relatively simple to investigate and clean. Let's take a look at the possible disadvantages of non-standard automation equipment.

As a fully automated equipment, automatic assembly machine is used by many enterprises. In the process of daily use, does it have easily worn parts? Xiaobian tells you that there are. Let's give you a brief introduction:
The worn parts of the automatic assembly machine are mainly the batch head and suction nozzle, of which the batch head wears the fastest, mainly because it often contacts the material, and there is friction between its rotation and the material, so the metal powder will adhere after a long time. The solution is also very simple and complex, that is, it is cleaned and replaced regularly. The second is the suction nozzle. Of course, it is also because it has been used for a long time. The solution is the same as the batch head.
Most of these two parts are customized according to the requirements of the manufacturer. When replacing the screw, remember to contact the seller to replace the screwdriver head and suction nozzle. When using the automatic assembly machine, please read the operation manual carefully to avoid safety problems.
Disadvantages of power supply:
This disadvantage is a static disadvantage. Most of these shortcomings are caused by the open circuit of the power line or the wrong connection of the ground wire, or the poor contact. Of course, it is also possible that the input voltage of the components of the equipment or the circuit board exceeds the allowable error planning, and the output voltage caused by the circuit shortcomings of the power component itself exceeds the allowable error planning.
Disadvantages of passive equipment:
This situation is mainly due to the open circuit caused by the open circuit of the capacitor, the loose and falling of the resistor end cap, the change of the resistance value and so on. If the resistance value is changed, it may cause confusion of logic value. If the capacitance value is changed, it may lead to poor decoupling, change of oscillator frequency and failure of motor and other equipment.
Poor power supply:
This problem usually occurs when the disturbing waveform is superimposed with the normal waveform. The ceramic chip capacitor with large capacity and excellent high-frequency function can be used to block these troubles.
In addition to the above shortcomings, there will also be software design shortcomings, equipment design shortcomings and poor contact. It is also difficult to prevent the shortcomings of non-standard automation equipment, but we must find out the causes of the problems, find out methods for the causes, make improvement or prevention, and there will be fewer and fewer shortcomings in the operation process of non-standard automation equipment.

The lighters parts are arranged in vibration with the screen machine, and then the parts are put into the lighter case through the flip plate, sliding plate and pressure plate. This method is simple, high yield and easy to operate. The investment cost is much less than the Automatic Production Line, only the corresponding plate is changed for the new model, other screen machine, press machine universal, greatly reduce the production cost.

◆ L*W*H：6M×4M×1.2M       
◆ Voltage：AC220V   
◆ Air pressure：0.6MP
◆ Weight：360KG   
◆ Item no：FT-FBZ-200
◆ Output：1-1.2Ten thousand/h   
◆ Operater staff：Six person
1、According to the requirements of the order, confirm repeatedly and then go to the warehouse to get the corresponding accessories.
2、Work flow:spacer-spring-wheel racket-adjust ring-lever-electrionic-pusher-flame guard.
3、In the process of production, there should be no shortage of parts, few parts or bad part.